Pool Dose Lab

Hot Tub Chemical Calculator

Enter your hot tub size and test results to get sanitizer, pH and alkalinity doses in grams, ounces and approximate teaspoons, for chlorine or bromine tubs.

Last reviewed · How we calculate

Your hot tub

Check your manual, or estimate it from the tub's size.

Sanitizer

Free chlorine, or total bromine for bromine tubs.

3–5 ppm is the usual range for either.

From dichlor use. Use 0 for bromine or a fresh fill.

pH and alkalinity

50–80 ppm is typical for hot tubs.

Your result

—

Hot tub volume
—
CYA added
—
Alkalinity
—
pH
—

    Teaspoon figures are approximate: granule size varies by brand. Weigh with a kitchen scale when you can, and add a little less than calculated in a small tub.

    How this hot tub chemical calculator works

    Hot tubs hold so little water that a few grams make a real difference. In a 400 gallon spa, 1 ppm of free chlorine is only about 1.5 g of available chlorine — less than a teaspoon of dichlor. This hot tub chemical calculator scales the same chemistry used for pools down to spa size and gives the result in grams, ounces and approximate spoons.

    Available chlorine (g) = ppm × gallons × 3.785 ÷ 1,000
    Product (g) = available chlorine ÷ strength · Bromine raised (ppm) ≈ chlorine added (ppm) × 2.25

    For pH and alkalinity it uses a carbonate-chemistry model of the water, which accounts for your current alkalinity and CYA. pH is lowered with dry acid (sodium bisulfate) and raised with soda ash (sodium carbonate); alkalinity is raised with baking soda (sodium bicarbonate).

    Worked example: 400 gallons, chlorine

    A 400 gallon tub reads 1 ppm FC, pH 7.8 and alkalinity 60 ppm. Raising FC to 4 ppm takes about 8.1 g of 56% dichlor, roughly 1.7 teaspoons, which also adds about 2.7 ppm of CYA. Raising alkalinity to 70 ppm takes about 25 g of baking soda (about 5.5 teaspoons). Lowering pH from 7.8 to 7.5 at that new alkalinity takes about 10 g of dry acid, roughly 1.75 teaspoons. Adjust alkalinity first, run the jets for 30 minutes, then retest pH — baking soda nudges pH up slightly, so the acid you need may change. If alkalinity is high and pH is low, lower alkalinity with acid and then raise pH by aerating with the jets; soda ash would push alkalinity back up.

    Small-dose reference

    Amount to raise free chlorine by 1 ppm
    Tub sizeDichlor 56%Liquid chlorine 12.5%Bleach 6%
    300 gal2.0 g (≈ 0.4 tsp)9.1 mL (≈ 1.8 tsp)18.4 mL (≈ 3.7 tsp)
    400 gal2.7 g (≈ 0.6 tsp)12.1 mL (≈ 2.5 tsp)24.5 mL (≈ 5.0 tsp)
    500 gal3.4 g (≈ 0.7 tsp)15.1 mL (≈ 3.1 tsp)30.7 mL (≈ 6.2 tsp)

    Liquid spoon figures are exact volume conversions (1 US teaspoon = 4.93 mL). Dry spoon figures assume about 4.7 g per level teaspoon of dichlor, based on a common label that equates half an ounce of granules with about a tablespoon; about 4.6 g per teaspoon of baking soda; and rough estimates of 5 g per teaspoon for soda ash and 6 g per teaspoon for dry acid. Bulk density varies with grain size, so a kitchen scale that reads to 1 g is more accurate.

    Chlorine or bromine

    Chlorine: dichlor granules are the classic hot tub chlorine because they dissolve fast and are pH-neutral. Each ppm of chlorine from dichlor also adds about 0.9 ppm CYA, so after a few weeks of daily dosing CYA can reach 30 ppm or more. A common approach is to start each fill with dichlor and switch to liquid chlorine or plain bleach once CYA reaches about 30 ppm.

    Bromine: a bromine tub needs a reserve of bromide ions in the water. Sodium bromide is added after each refill — labels commonly call for about half an ounce per 100 gallons, which works out to roughly 30 ppm of bromide. An oxidizer (chlorine or a non-chlorine shock) then converts bromide into active bromine. Bromine is measured on a heavier scale: 1 ppm of free chlorine becomes about 2.25 ppm of bromine, so the calculator divides your bromine increase by 2.25 to get the chlorine dose. Dichlor works as the oxidizer but adds CYA that a bromine tub does not need; unscented bleach or liquid chlorine avoids that.

    Bromine tablets: most are BCDMH (bromo-chloro-dimethylhydantoin), which carries both bromine and chlorine. They dissolve slowly in a floater or feeder, so you set the output by adjusting the feeder rather than by calculating a dose. The dimethylhydantoin left behind builds up over time and, like CYA, makes the bromine less active, which is one reason bromine tubs need regular draining. Tablets also tend to pull pH down. Use the calculator for corrections, not to dose tablets.

    How to add chemicals to a hot tub

    1. Test sanitizer, pH and alkalinity. Strips are fine for a quick look; a drop kit is more precise.
    2. Turn the jets on with the cover open. Add one chemical at a time, starting with alkalinity, then pH, then sanitizer.
    3. Sprinkle granules over the water near the jets or pre-dissolve them in a cup of tub water. Pour liquids slowly into the moving water.
    4. Wait 20 to 30 minutes between chemicals and retest before the next one.
    5. Leave the cover open for a few minutes after a large chlorine dose so the gas does not collect under it.

    Add chemicals to water, never water to chemicals. Never mix chemicals in the same cup, and never combine acid with chlorine or two chlorine products. Use separate, labelled measuring spoons, wear eye protection, and follow the product label, which takes precedence over these figures.

    Target ranges for hot tubs

    Common guidelines are free chlorine 3 to 5 ppm or bromine 3 to 5 ppm, pH 7.4 to 7.6, total alkalinity 50 to 80 ppm, calcium hardness 150 to 250 ppm and CYA 0 to 30 ppm. Hot water and jets drive off carbon dioxide, so pH tends to rise; keeping alkalinity at the low end of the range slows that drift. The CDC recommends at least 3 ppm free chlorine or 4 ppm bromine for public hot tubs.

    If chemicals stop behaving — sanitizer disappears fast, foam builds, or the water looks dull even when balanced — it may be time for fresh water. The hot tub drain and refill calculator estimates when. Not sure of your volume? Use the hot tub volume calculator, because every dose here scales with it.

    Questions people ask

    How much dichlor do I put in a 400 gallon hot tub?

    About 2.7 g of 56% dichlor raises free chlorine by 1 ppm in 400 gallons, a little over half a teaspoon. Going from 1 to 4 ppm takes about 8 g, roughly 1.7 teaspoons.

    What chemical levels should a hot tub have?

    Common guidelines are free chlorine 3 to 5 ppm or bromine 3 to 5 ppm, pH 7.4 to 7.6, total alkalinity 50 to 80 ppm, calcium hardness 150 to 250 ppm and CYA no more than 30 ppm. The CDC recommends at least 3 ppm chlorine or 4 ppm bromine for public hot tubs.

    How do I convert chlorine ppm to bromine ppm?

    Multiply by 2.25. Bromine atoms are about 2.25 times heavier than chlorine, so 1 ppm of free chlorine converts to about 2.25 ppm of bromine when there is bromide in the water.

    How much baking soda do I add to my hot tub?

    About 25 g (roughly 5.5 teaspoons, under 2 tablespoons) of baking soda raises total alkalinity by 10 ppm in 400 gallons. Add it with the jets running and retest after 30 minutes.

    Should I use chlorine or bromine in my hot tub?

    Both work. Chlorine is cheaper and easy to measure; dichlor adds CYA, so many owners switch to liquid chlorine or bleach as CYA rises. Bromine holds up better at high temperatures and smells less, but needs a bromide reserve and builds up by-products that are removed only by draining.

    Sources and references