Pool Dose Lab

Pool Pump Size Calculator

Enter your pool volume and turnover time to get the flow rate your pump needs, then compare what a single-speed and a variable-speed pump cost to run at your electricity price.

Last reviewed · How we calculate

Flow you need

Not sure? Work it out from your pool's size.

Hours to pass the whole pool through the filter once.

Single-speed pump

Volts × amps from the motor label is close enough.

Variable-speed pump

Use the same as the single-speed for a like-for-like comparison.

Many owners filter at 1,200–2,000 rpm.

Electricity

Example — use the rate on your electric bill.

About 6 for a pool closed in winter.

Your result

—

Flow per hour
—
For a 6-hour turnover
—
For a 10-hour turnover
—
Single-speed energy
—
Single-speed per month
—
Single-speed per year
—
Variable-speed power
—
Hours to move the same water
—
Variable-speed energy
—
Variable-speed per month
—
Variable-speed per year
—
Estimated savings
—

Variable-speed watts use the ideal cube rule; real pumps draw somewhat more at low speed. Check your pump's display or spec sheet for actual watts at your rpm and enter it as full-speed watts with 3,450 rpm for an exact figure.

How the pool pump size calculator works

Pump sizing starts with flow, not horsepower. A pool pump size calculator asks one question first: how many gallons per minute must move through the filter to pass the whole pool through it in your chosen turnover time? That flow — and the resistance of your pipes and filter — is what decides which pump fits. Horsepower is only the motor's rating; two pumps with the same horsepower can deliver very different flows on the same plumbing.

Required flow (gpm) = pool gallons ÷ (turnover hours × 60) Single-speed cost = watts × hours ÷ 1,000 × price per kWh Variable-speed watts ≈ full-speed watts × (rpm ÷ 3,450)³ Variable-speed hours for the same water = single-speed hours × 3,450 ÷ rpm

Choosing a turnover time

A widely used residential guideline is to turn the water over at least once a day, and an 8-hour turnover is a common design point. Commercial pools follow local health codes with much shorter turnovers. Shorter turnovers mean a bigger flow, more pipe friction and more power; longer ones save energy as long as the water stays clear and the chlorine holds. Pools with heavy debris, high bather loads or a salt generator that only makes chlorine while the pump runs often need more hours.

Required flow (gpm) by pool size and turnover time
Pool size6 hours8 hours10 hours
10,000 gal27.820.816.7
15,000 gal41.731.325.0
20,000 gal55.641.733.3
25,000 gal69.452.141.7
30,000 gal83.362.550.0

Matching a pump to the flow

Every pump has a performance curve that shows flow against total dynamic head — the resistance from pipe length, fittings, the filter and any heater or cleaner. To pick a pump, estimate your system's head (a pool professional can measure it with pressure and vacuum gauges), then find a pump that delivers your required gpm at that head. Also check that the flow does not exceed the maximum rating of your filter, heater or salt cell. An oversized pump on small plumbing mostly converts electricity into noise, heat and filter wear.

Single-speed vs variable-speed running cost

Pump power follows the affinity laws: flow rises in proportion to speed, but power rises roughly with the cube of speed. ENERGY STAR puts it simply — cutting pump speed in half lets the pump use about one-eighth as much energy. Because half the speed also means half the flow, you run twice as long to move the same water, and still use about a quarter of the energy.

Worked example with the default numbers: a 1,800 W single-speed pump running 8 hours a day uses 14.4 kWh, which at $0.17 per kWh is about $74 a month and $894 a year. A variable-speed pump with the same full-speed draw, slowed to 1,500 rpm, draws about 148 W by the cube rule and needs about 18.4 hours to move the same water: 2.72 kWh a day, or about $169 a year. The estimated saving is about $725 a year (81%).

1,800 W pump, same daily water as 8 hours at full speed, $0.17 per kWh
Speed (rpm)Watts (cube rule)Hours per daykWh per dayCost per year
3,4501,8008.014.40$894
2,8009629.99.49$589
2,40060611.56.97$432
2,00035113.84.84$300
1,75023515.83.71$230
1,50014818.42.72$169
1,2007623.01.74$108

Treat these as best-case figures. Real motors and drives are less efficient at low speed, and a pool's plumbing does not behave like the perfect system the cube rule assumes, so a real pump at 1,500 rpm often draws more than the table shows. Most variable-speed pumps display actual watts; enter that number with 3,450 rpm as the speed and the calculator will use it directly. Also note the limits: at very low speeds you may not have enough flow for a heater, a pressure-side cleaner, a salt cell's flow switch or skimming, so many owners run a short higher-speed block each day.

The 2021 Department of Energy pool pump rule

The US Department of Energy set efficiency standards for dedicated-purpose pool pumps manufactured on or after July 19, 2021. Covered pumps must carry a weighted energy factor (WEF) rating in gallons per watt-hour and meet a minimum that depends on the pump's class and hydraulic horsepower, for pumps up to 2.5 hydraulic horsepower. In practice, manufacturers have said most single- and two-speed self-priming filter pumps of about 1 total horsepower and above cannot meet the standard, so replacement pumps in that range are variable-speed. Smaller pumps, some exempt types and pumps already in the supply chain before the date are treated differently; your installer can confirm what applies.

Related equipment calculations

Heaters need a minimum flow to fire, so size the pump with the pool heater size calculator in mind. If you run a salt system, chlorine output depends on pump hours, so check your levels with the chlorine calculator after changing your schedule. And if your gallons are a guess, start with the pool volume calculator, because every flow figure above scales directly with volume.

Questions people ask

What size pump do I need for a 15,000 gallon pool?

To turn 15,000 gallons over once in 8 hours you need about 31 gallons per minute; for a 6-hour turnover, about 42 gpm. Choose a pump whose performance curve delivers that flow at your plumbing's resistance (head), not just a horsepower number.

How many hours a day should a pool pump run?

A widely used guideline is one full turnover a day, which for most residential pools means 6 to 12 hours depending on pump flow. With a variable-speed pump, running longer at a low speed moves the same water for much less electricity.

How much does it cost to run a pool pump?

A 1,800 W single-speed pump running 8 hours a day uses 14.4 kWh, which at $0.17 per kWh is about $74 a month or $894 a year. The same water moved by a variable-speed pump at 1,500 rpm costs about $169 a year by the cube-rule estimate.

Do variable-speed pool pumps really save money?

Yes, because power drops much faster than flow: ENERGY STAR notes that halving pump speed lets the pump use about one-eighth as much energy. Real savings are smaller than the ideal cube rule because motors and drives lose efficiency at low speed, but they are usually large compared with a single-speed pump.

Are single-speed pool pumps still legal?

Under the US Department of Energy standard for dedicated-purpose pool pumps that took effect July 19, 2021, most self-priming filter pumps of about 1 total horsepower and above effectively need variable-speed operation to comply. Smaller pumps and some exempt types can still be single-speed, and pumps already in the supply chain could still be sold.

Sources and references