Pool Salt Calculator
Enter your pool size and salt reading to see exactly how many pounds and 40 lb bags to add — or how much water to replace if the level is too high.
Last reviewed · How we calculate
Your result
—
- Pool volume
- —
- Change needed
- —
- Bags to buy
- —
- First addition (75%)
- —
- Water to replace
- —
Add about three-quarters, brush it in, run the pump 24 hours, then retest before adding the rest. Generator readouts can drift — confirm with a salt test strip or meter.
How the salt calculation works
Salt is measured in parts per million (ppm), which for pool water is the same as milligrams per liter. One gallon of water weighs about 8.345 lb, so raising one gallon by 1 ppm takes 8.345 millionths of a pound of salt. Multiply that by your pool's gallons and by the number of ppm you need, and you have the pounds to add.
Salt (lb) = (target ppm − current ppm) × gallons × 8.345 ÷ 1,000,000
Bags are rounded up to the next whole 40 lb bag, because that is how pool salt is sold in most US stores. If your store sells 50 lb or 25 kg bags, divide the pounds (or kilograms) shown by that bag size instead.
Worked example: 15,000 gallons from 2,600 to 3,200 ppm
The pool needs 600 ppm more. 600 × 15,000 × 8.345 ÷ 1,000,000 = 75.1 lb, so you would buy two 40 lb bags and add a little under two bags' worth. For a brand-new 15,000 gallon salt pool starting at 0 ppm, the same math gives about 401 lb — just over ten bags.
| Pool size | Salt (lb) | 40 lb bags |
|---|---|---|
| 5,000 gal | 134 | 4 |
| 10,000 gal | 267 | 7 |
| 15,000 gal | 401 | 11 |
| 20,000 gal | 534 | 14 |
| 25,000 gal | 668 | 17 |
| 30,000 gal | 801 | 21 |
Pick the right target
Your salt chlorine generator (also called a salt cell or SWG) only makes chlorine efficiently inside the salt range its maker specifies. Most residential units are built for roughly 2,700 to 3,400 ppm, and 3,200 ppm is a common recommended level. Running too low can make the cell shut off or wear faster; running far too high wastes salt and can trigger a high-salt warning. Use the number printed in your manual rather than a general rule.
How to add salt
- Test the water with a salt test strip or a calibrated meter — do not rely only on the generator display.
- Turn the generator off (leave the pump running) so the cell does not read undissolved salt.
- Pour salt into the shallow end or around the perimeter, away from the skimmer, and brush it toward the main drain.
- Circulate for 24 hours, then retest before adding the remaining amount.
- Turn the generator back on once the reading is inside the range.
Salt only leaves the pool with water — splash-out, backwashing, draining or heavy rain overflow. Evaporation does not remove salt, so topping up with fresh water slowly lowers the reading only if water also leaves the pool.
When the salt is too high
Because salt does not break down, lowering it means diluting. The share of water to replace is (current − target) ÷ (current − fill-water salt). Going from 4,000 to 3,200 ppm with ordinary tap water means replacing about 20% of the pool. Drain in stages if your pool type or groundwater level makes a large drain risky, and check with a pool professional before draining a vinyl or fiberglass pool far down.
Salt and the rest of your water balance
Salt pools still need chlorine stabilizer (cyanuric acid), balanced pH and alkalinity. Salt cells tend to push pH upward, so many owners keep total alkalinity on the lower side. After adjusting salt, check your stabilizer level and use the chlorine calculator to set the free chlorine target that matches it.
Questions people ask
How much salt do I need for a 15,000 gallon pool?
Starting from fresh water (0 ppm), reaching 3,200 ppm in 15,000 gallons takes about 401 lb of salt — just over ten 40 lb bags, so buy eleven and add the last one only after retesting. If you already have 2,600 ppm, you only need about 75 lb, or two bags.
How much does one 40 lb bag raise the salt level?
One 40 lb bag raises a 10,000 gallon pool by about 480 ppm and a 20,000 gallon pool by about 240 ppm. The bigger the pool, the smaller the change from each bag.
What salt level should a saltwater pool have?
Most residential salt chlorine generators are designed for roughly 2,700 to 3,400 ppm, and 3,200 ppm is a common target. Your generator's manual gives the exact range, and that range is the one to follow.
Can I use any salt in my pool?
Use plain sodium chloride sold for pools, at least 99% pure, with no iodine, anti-caking agents or yellow prussiate of soda. Rock salt and table salt can stain surfaces or add impurities.
How do I lower the salt level in my pool?
Salt does not evaporate or break down, so the only way to lower it is to drain some water and refill with fresh water. The calculator shows what share of the water to replace.