Pool Dose Lab

Pool Opening Checklist

Enter your pool size and first test results to get a step-by-step opening checklist with the exact amounts of each chemical for your pool, ready to print.

Last reviewed · How we calculate

Your pool

Not sure? Work it out from your pool's size.

Surface
Chlorine source
First test results
Products you use

Your result

—

Chlorine goal
—
Chemicals to add
—

    Add one product at a time with the pump running, wait at least an hour (overnight for calcium and stabilizer), and retest before the next. Never mix chemicals together.

    How to use this pool opening checklist

    Opening a pool goes faster when the steps happen in the right order and you know the amounts before you start. This pool opening checklist builds the list from your pool size, surface and first test results, so each chemical step shows a real amount for your water instead of "follow the label". Test after the water has circulated for a few hours, enter the numbers, and print the result to take outside.

    Amounts use the same formulas as the rest of the site. The chlorine goal follows the stabilizer ratio used across these calculators — a widely used guideline is free chlorine at about 11.5% of CYA for everyday levels and about 40% of CYA to clear cloudy or green water (salt pools run lower everyday levels, about 7.5% of CYA). The balance targets are common guidelines: pH 7.4–7.6, alkalinity around 80 ppm (70 ppm for salt pools), calcium around 300 ppm for plaster and 200 ppm for vinyl or fiberglass, and stabilizer around 40 ppm (70 ppm with a salt generator).

    Step by step: what each item means

    Clear and remove the cover. Pump standing water off a solid cover and sweep off leaves before you unhook it; most opening-day mess is cover debris that slides into the pool. Hose the cover, let it dry fully and store it folded somewhere rodents cannot reach.

    Reconnect the equipment. Pull the winter plugs from return lines and skimmers, remove ice compensators, reinstall drain plugs on the pump, filter and heater, and reconnect hoses on an above-ground pool. Replace any cracked O-rings while everything is apart; a dab of silicone lubricant (not petroleum jelly) keeps them sealing.

    Raise the water level. Bring it to the middle of the skimmer opening. The fill time calculator estimates how long that takes.

    Start the pump and filter. Prime the pump, open the valves and watch for leaks. Write down the filter pressure when it is clean — it tells you later when to clean or backwash. Run the heater only after flow is steady.

    Clean the pool. Skim, brush and vacuum before balancing so chlorine is not wasted on leaves. For a green pool, vacuum heavy debris to waste so it does not choke the filter.

    Balance in order. Alkalinity comes first because it buffers pH; then pH; then calcium; then stabilizer. The checklist marks readings that are already in range so you can skip them. If alkalinity is high, the acid is added in portions over several days and pH is brought back up by aeration (fountains, return jets aimed upward), which raises pH without adding the alkalinity back.

    Shock or raise chlorine last. Chlorine works best once pH is in range. For clear water the checklist raises free chlorine to your everyday target. For cloudy or green water it uses a shock level of about 40% of CYA and asks you to hold it there — test and top up two or three times a day — until the water is clear, combined chlorine is 0.5 ppm or less, and the pool loses no more than 1 ppm of free chlorine overnight. The pool shock calculator covers that process in detail.

    Salt pools. Salt does not leave with evaporation, but rain overflow and draining dilute it. Add salt if needed, brush it in and wait a day before switching the cell on. Shock with chlorine from a bottle; a generator is too slow to clear a cloudy pool.

    Worked example: 15,000 gallon plaster pool, cloudy

    With the default inputs — free chlorine 0, pH 7.8, alkalinity 60, calcium 200, stabilizer 20 — the checklist adds about 4.2 lb of baking soda (alkalinity to 80), about 11.4 fl oz of 31.45% muriatic acid (pH to 7.5), about 14.6 lb of 94–97% calcium chloride (calcium to 300), and about 2.5 lb of stabilizer (CYA to 40). With CYA at 40, the shock level is 16 ppm, which takes about 1.92 gallons of 12.5% liquid chlorine to reach from zero.

    Quick dose reference per 10,000 gallons
    To raiseProductAmount
    Alkalinity by 10 ppmBaking soda1.4 lb
    Calcium by 10 ppmCalcium chloride 94–97%0.97 lb
    Stabilizer by 10 ppmCyanuric acid13.4 oz (weight)
    Free chlorine by 1 ppmLiquid chlorine 12.5%10.2 fl oz

    Safety: wear eye protection and gloves. Always add chemicals to water, never water to chemicals. Never mix acid and chlorine, or two different chlorine products, in the same container or let them meet in the skimmer — the reaction can release chlorine gas or start a fire. Add acid and chlorine at least an hour apart with the pump running, and follow every product label.

    Common opening mistakes

    • Shocking before cleaning and balancing, then wondering why the chlorine disappears.
    • Adding everything at once. Some products cloud the water or react with each other; one at a time is slower but predictable.
    • Guessing the volume. Every amount on this list scales with gallons, so a wrong volume makes every dose wrong — check it with the pool volume calculator.
    • Adding stabilizer by habit. It builds up, and high CYA means you need more chlorine for the same effect; the cyanuric acid calculator shows how to bring it down.

    After the first 24 hours, run a full test and use the pool chemical calculator for any fine-tuning. When the season ends, the pool closing checklist does the same job in reverse.

    Questions people ask

    What do I add first when opening a pool?

    Get the water circulating and clean first, then test and adjust in order: alkalinity, pH, calcium, stabilizer, and chlorine last. Add one chemical at a time with the pump running and wait for each to mix before the next.

    How much shock do I need to open a green pool?

    A common method is to raise free chlorine to about 40% of your stabilizer (CYA) level and hold it there until the water is clear. At 40 ppm CYA that is 16 ppm; in a 15,000 gallon pool starting from zero, that takes about 1.92 gallons of 12.5% liquid chlorine, plus top-ups as it is used up.

    How long does it take to open a pool?

    With clear water, opening takes a day: a few hours of work and 24 hours of circulation before the final retest. Cloudy water usually needs about 2 days, and a green pool commonly needs 3 to 5 days of holding shock level.

    When can you swim after opening a pool?

    Once free chlorine has fallen back to your normal target range and pH is 7.2 to 7.8. After shocking to 16 ppm, that can take a day or more; test before swimming rather than counting hours.

    Should I add stabilizer when opening the pool?

    Only if your test shows it is low. Stabilizer does not evaporate, so many pools still have most of last year's. Rain and water replacement lower it; if it reads under about 30 ppm (60 ppm for salt pools), top it up.

    Sources and references