Pool Dose Lab

Pool Shock Calculator

Pick why you are shocking, enter your pool size, chlorine and stabilizer readings, and get the amount of shock in pounds, 1 lb bags or gallons.

Last reviewed · How we calculate

Your pool

Not sure? Work it out from your pool's size.

Why are you shocking?
Test results

Use 0 for an unstabilized indoor pool.

Total chlorine minus free chlorine. Used in combined chlorine mode.

Used in routine mode. 10 ppm is a common choice.

Product

Trichlor tablets are not used for shocking; they dissolve too slowly and add a lot of CYA.

Your result

—

Pool volume
—
Shock level
—
Raise free chlorine by
—
1 gallon jugs
—

    Shock in the evening with the pump running so sunlight does not burn off the chlorine before it works. Retest before adding more.

    How much shock to add to a pool

    Shocking means raising free chlorine (FC) well above its everyday level for a while, to kill algae or burn off combined chlorine. How much shock to add to a pool depends on the pool's volume, your current FC, the strength of the product, and — the part most labels skip — how much cyanuric acid (CYA) is in the water. This pool shock calculator handles three cases:

    • Algae or cloudy water (SLAM): raise FC to about 40% of CYA and hold it there. SLAM stands for Shock, Level, And Maintain, the process used by the Trouble Free Pool method.
    • Combined chlorine: raise FC to 10 times the combined chlorine (CC) reading, the classic breakpoint rule.
    • Routine shock: raise FC to a fixed level you choose, often 10 ppm, for example after a pool party or heavy rain.

    Shock level (SLAM) ≈ 0.40 × CYA · Breakpoint level = 10 × CC
    Chlorine to add (ppm) = shock level − current FC

    The dose itself is the same arithmetic as the pool chlorine calculator: ppm × gallons × 3.785 ÷ 1,000 gives grams of available chlorine, which is divided by the strength of the product. In an indoor pool with no CYA, the tool uses 10 ppm as the shock level.

    Worked example: algae in 20,000 gallons

    A 20,000 gallon pool has 50 ppm CYA, 2 ppm FC and a green tint. The SLAM level is 0.40 × 50 = 20 ppm, so FC needs to rise by 18 ppm. That takes about 461 fl oz (3.6 gallons) of 10% liquid chlorine, or about 4.1 lb of 73% cal-hypo — just over four 1 lb bags. Dichlor would need about 5.4 lb and would add roughly 16 ppm of CYA, raising the shock level you have to hold the next day. That is why liquid chlorine is the usual choice for algae.

    Why "one bag per 10,000 gallons" depends on CYA

    Many bags of shock say one pound treats 10,000 gallons. One 1 lb bag of 73% cal-hypo raises 10,000 gallons by about 8.7 ppm, and a 65% bag by about 7.8 ppm. Whether that is enough depends on your stabilizer, because CYA binds most of the free chlorine and the shock level rises with it.

    Shock level by CYA and product needed from 0 ppm FC, per 10,000 gallons
    CYA (ppm)Shock level (ppm FC)Cal-hypo 73%Liquid chlorine 10%
    0 (indoor)101.1 lb1.0 gal
    30121.4 lb1.2 gal
    40161.8 lb1.6 gal
    50202.3 lb2.0 gal
    60242.7 lb2.4 gal
    80323.7 lb3.2 gal
    100404.6 lb4.0 gal

    At 30 ppm CYA one bag per 10,000 gallons gets you most of the way. At 80 ppm it delivers about a quarter of what is needed, which is why algae often comes back after a "shock" that followed the bag directions. Subtract whatever FC you already have.

    How to shock a pool

    1. Test FC, CC and CYA. Adjust pH toward 7.2 to 7.6 first; chlorine works faster at lower pH.
    2. Brush the walls and floor, and clean the filter if it is loaded with debris.
    3. With the pump running, pour liquid chlorine in front of a return. Dissolve cal-hypo in a bucket of pool water first, adding the granules to the water.
    4. For a SLAM, retest every few hours and top up to keep FC at the shock level. Keep going until the water is clear, CC is 0.5 ppm or less, and FC drops no more than 1 ppm overnight — the usual Trouble Free Pool finish test.
    5. For combined chlorine, retest after a few hours. If CC is still above 0.5 ppm, raise FC again.

    Never mix cal-hypo with trichlor or any other chlorine product, even in a skimmer or bucket — the combination can ignite or explode. Never mix chlorine with acid. Store shock dry and cool, add it to water rather than water to it, wear eye protection and follow the label.

    Common shocking mistakes

    • Shocking once and stopping. Algae needs FC held at the shock level until it is gone, which can take days.
    • Shocking with dichlor all summer. Each SLAM can add 10 to 20 ppm of CYA, and a higher CYA means a higher shock level next time. Track it with the cyanuric acid calculator.
    • Shocking in bright sun. Unstabilized chlorine breaks down quickly in sunlight, so evening doses last longer.
    • Using the wrong target. Look up your exact level on the chlorine CYA chart.

    Shocking does not replace day-to-day chlorine. If you need to shock often, your everyday FC is probably too low for your CYA level.

    Questions people ask

    How much shock do I add to my pool?

    Enough to raise free chlorine to the shock level for your stabilizer, which is about 40% of your CYA. A 20,000 gallon pool at 50 ppm CYA and 2 ppm FC needs about 3.6 gallons of 10% liquid chlorine or 4.1 lb of 73% cal-hypo to reach 20 ppm.

    Is one bag of shock per 10,000 gallons enough?

    A 1 lb bag of 73% cal-hypo raises 10,000 gallons by about 8.7 ppm. That is close to a shock level only when CYA is around 20 to 30 ppm; at 50 ppm CYA the shock level is 20 ppm, so you would need over two bags.

    How much shock do I need for combined chlorine?

    A common rule is to raise free chlorine to 10 times the combined chlorine reading. With 0.6 ppm CC and 2 ppm FC in 20,000 gallons, that means adding 4 ppm, about 102 fl oz of 10% liquid chlorine.

    Can I swim after shocking the pool?

    Follow the product label first. The safe general rule is to wait until free chlorine has fallen back to your normal target range and pH is 7.2 to 7.8 — test rather than counting hours. After a shock to 10 ppm or more, that usually takes a day or longer.

    Should I use liquid chlorine or granular shock?

    Liquid chlorine adds nothing besides chlorine and salt, so it suits repeated shocking. Cal-hypo adds about 0.7 ppm calcium per ppm of chlorine, and dichlor adds about 0.9 ppm CYA per ppm, which builds up quickly at shock doses.

    Sources and references