Pool Chemical Calculator
Enter your test-kit readings, pool type and products, and get every adjustment in the order to make it, with exact amounts and the water's saturation index (LSI).
Last reviewed · How we calculate
Your result
—
- Pool volume
- —
- Saturation index (LSI) now
- — BalancedCorrosiveScaling
- LSI after this plan
- —
- Free chlorine for your CYA
- —
Wait times: run the pump throughout. Allow about 30 minutes after chlorine and about an hour after acid, baking soda or soda ash before retesting or adding the next product. Stabilizer can take 2–7 days to fully dissolve and show on a test. Amounts are estimates — add about three-quarters, then retest.
How this pool chemical calculator builds your plan
A pool chemical calculator is most useful when it answers the question you actually have after testing: what do I add first, and how much? This one takes a full set of readings — free chlorine, pH, total alkalinity, calcium hardness, cyanuric acid, water temperature and, for salt pools, salt — and compares each one with the common target range for your type of pool. Anything outside its range becomes a numbered step with a dose for the product you selected. Anything already in range is listed as OK so you can see the whole picture, not just the problems.
The order matters because the readings affect each other. Total alkalinity is the water's buffer, so it decides how much acid or soda ash a pH change takes; adjusting it first stops you from chasing pH. Chlorine comes after pH because chlorine works better and tests more reliably near pH 7.5. Stabilizer and calcium change slowly and barely move pH, so they come next, and salt is last because it does not affect the other readings.
Order: total alkalinity → pH → free chlorine → cyanuric acid → calcium hardness → salt
Target ranges this pool water chemistry calculator uses
These are widely used guidelines for residential pools, not legal limits. Your surface warranty, generator manual or local health code may give different numbers, and those should win.
| Reading | Chlorine pool | Salt generator pool |
|---|---|---|
| pH | 7.4–7.6 (7.2–7.8 acceptable) | 7.4–7.6 (7.2–7.8 acceptable) |
| Total alkalinity | 70–90 ppm (up to 120 on plaster) | 60–80 ppm |
| Cyanuric acid | 30–50 ppm | 60–80 ppm |
| Free chlorine | about 11.5% of CYA (minimum 7.5%) | about 7.5% of CYA (minimum 5%) |
| Calcium hardness | 250–350 ppm plaster or pebble; 150–300 ppm vinyl or fiberglass | |
| Salt | — | 2,700–3,400 ppm (per manual) |
| LSI | −0.3 to +0.3 | |
Free chlorine is tied to stabilizer because cyanuric acid holds most chlorine in a reserve form that does not sanitize as quickly. More CYA protects chlorine from sunlight but means you need a higher free chlorine level for the same effect. The chlorine and CYA chart lists the levels for each CYA reading.
Worked example
Take a 15,000 gallon plaster pool on liquid chlorine with these readings: FC 2.5 ppm, pH 7.9, TA 70 ppm, CH 220 ppm, CYA 30 ppm, water at 82 °F. Alkalinity is in range, so step 1 is OK. pH is above 7.8, so step 2 is about 13.6 fl oz (401 mL) of 31.45% muriatic acid to reach 7.5. With 30 ppm CYA the chlorine target is 3.5 ppm, so step 3 is about 15.4 fl oz of 12.5% liquid chlorine. CYA is fine. Calcium is below 250, so step 5 is about 11.7 lb of 94–97% calcium chloride to reach 300 ppm. That is three adjustments. The LSI starts at about +0.19 and ends near −0.07, both inside the balanced band.
Wait times between additions
- Run the pump for the whole process and add each product in front of a return jet, away from the skimmer.
- After acid, baking soda or soda ash, a common guideline is to wait about an hour, then retest pH before the next pH-related product.
- After liquid chlorine, about 30 minutes of circulation is usually enough to retest. Do not add chlorine and acid at the same time or in the same spot.
- Pre-dissolve calcium chloride in a bucket of pool water; it releases heat. Add it slowly and give it a few hours before retesting hardness.
- Stabilizer granules dissolve slowly. Put them in a sock or skimmer basket as the label directs, and do not backwash for several days.
Safety: always add chemicals to water, never water to chemicals. Never mix acid with chlorine, or two different chlorine products, in a bucket or feeder. Wear eye protection and gloves, keep products sealed and apart, and follow each label.
Shock levels and algae
If free chlorine is below the minimum for your CYA, or you tick the algae box, step 3 changes from a top-up to a shock: raise FC to about 40% of the CYA reading and hold it there, adding chlorine as it drops, until the water is clear and the pool loses less than 1 ppm overnight. With 30 ppm CYA that shock level is 12 ppm. The pool shock calculator covers that process in more detail.
Common mistakes
- Adding everything at once. Doses are estimates; each correction changes the next one, so retest between steps.
- Using stabilized chlorine every day. Dichlor and trichlor add CYA with every dose, so CYA climbs and the chlorine you need climbs with it.
- Raising calcium in a vinyl pool to plaster levels. Vinyl and fiberglass do not need as much, and high calcium with high pH leads to scale.
- Trusting an old test. Reagents expire; replace them as the kit maker recommends.
For a single reading in more depth, use the pH calculator, the alkalinity calculator or the LSI calculator.
Questions people ask
In what order should I add pool chemicals?
A widely used order is total alkalinity first, then pH, then chlorine, then stabilizer (CYA) and calcium, and salt last on salt pools. Alkalinity comes first because it changes how much acid or soda ash a pH correction needs.
How long should I wait between adding pool chemicals?
With the pump running, a common guideline is about 30 minutes after liquid chlorine and about an hour after acid, baking soda or soda ash before retesting or adding the next chemical. Stabilizer granules can take 2 to 7 days to fully show on a test.
Can I add chlorine and acid at the same time?
No. Never mix them or pour them into the same spot, because together they release chlorine gas. Add one, let it circulate, then add the other in a different spot in front of a return jet.
What are normal pool chemical levels?
Common guidelines are pH 7.4 to 7.6, total alkalinity 70 to 90 ppm (60 to 80 for salt pools), calcium hardness 250 to 350 ppm for plaster, and CYA 30 to 50 ppm (60 to 80 for salt pools). Free chlorine depends on CYA: about 11.5% of the CYA reading, so 4.6 ppm at 40 ppm CYA.
How much muriatic acid do I add to a 15,000 gallon pool?
It depends on alkalinity and stabilizer as well as pH. With TA 70 and CYA 30, lowering pH from 7.9 to 7.5 takes about 13.6 fl oz of 31.45% muriatic acid by this calculator's model; add about three-quarters and retest.